Legacy For existing JADConfig systems only.
End of Support Notice: JADConfig systems will reach End of Support on January 1, 2027. Migration to AMP will be required before the Just Add Power Support Team can provide further troubleshooting or system service.
See JADConfig End of Support Notice for requirements and migration-planning information.
Overview
This article identifies switch models that JADConfig can configure in existing systems. Every model listed has been discontinued by its manufacturer. This information is retained to help identify installed hardware and plan a migration to AMP.
Do not use JADConfig to configure a new system or expand an existing system. Use AMP with a currently supported switch. See Choosing the Right Switch for AMP Standardized Systems for current switch options.
Migrate to AMP
Select the article that matches the existing JADConfig system:
- Convert an Established 2G Series JADConfig System to AMP
- Convert an Established Omega Series or Ultra Series JADConfig Single-Switch System to AMP
- Convert an Established Omega Series or Ultra Series JADConfig Stack-Switch System to AMP
JADConfig Switch Reference
The following tables are provided for legacy hardware identification and migration planning. They are not a list of switches approved for new systems, replacements, or system expansions.
Control-system drivers for these legacy switch models remain available in Switch Drivers.
For information about existing systems that use more than one switch, see Multi-Switch Considerations for JADConfig Systems.
Luxul Switches
| Model | Ports On | Max Devices | PoE Ports | Multi-Switch | Manufacturer Status |
|---|---|---|---|---|---|
| AMS-1208P | Rear | 9 | 7 |
Discontinued |
|
| AMS-1816P | Rear | 17 | 15 |
Discontinued |
|
| AMS-2600 | Rear | 25 | 0 |
Discontinued |
|
| AMS-2616P | Rear | 25 | 16 |
Discontinued |
|
| AMS-2624P | Rear | 25 | 23 |
Discontinued |
|
| AMS-4424P | Rear | 23 | 23 | Yes |
Discontinued |
| XMS-1208P | Front | 9 | 7 |
Discontinued |
|
| XMS-2624P | Front | 25 | 23 |
Discontinued |
|
| XMS-5248P | Front | 47 | 47 |
Discontinued |
|
| XMS-7048P | Front | 47 | 47 | Yes |
Discontinued |
| SW-510-48P-F | Front | 47 | 47 |
Discontinued |
|
| SW-610-24P-R | Rear | 23 | 23 | Must use AMP |
Discontinued |
| SW-610-48P-F | Front | 47 | 47 | Must use AMP |
Discontinued |
Cisco Switches
| Model | Ports On | Maximum Devices | PoE Ports | Multi-Switch | Status |
|---|---|---|---|---|---|
| CBS350-8P-2G | Front | 6 | 9 |
Discontinued |
|
| CBS350-8P-E-2G | Front | 6 | 9 |
Discontinued |
|
| CBS350-8FP-2G | Front | 8 | 9 |
Discontinued |
|
| CBS350-8FP-E-2G | Front | 8 | 9 |
Discontinued |
|
| CBS350-16P-2G | Front | 12 | 15 |
Discontinued |
|
| CBS350-16P-E-2G | Front | 12 | 15 |
Discontinued |
|
| CBS350-16FP-2G | Front | 15 | 15 |
Discontinued |
|
| CBS350-24P-4G | Front | 19 | 23 |
Discontinued |
|
| CBS350-24FP-4G | Front | 23 | 23 |
Discontinued |
|
| CBS350-48P-4G | Front | 37 | 47 |
Discontinued |
|
| CBS350-48FP-4G | Front | 47 | 47 |
Discontinued |
|
| SG300 | Front | 10/28/52 | 9/27/51 |
Discontinued |
|
| SG350 | Front | 10/28/52 | 9/27/51 |
Discontinued |
|
| SG500(X) | Front | 28/48/52 | 27/47/47 | Yes |
Discontinued |
| SG550X | Front | 28/48 | 27/47 | Yes |
Discontinued |
| The SG350X is not supported. The SG550X was the supported model for existing multi-switch JADConfig systems. | |||||
