-
Configure Video and Audio on Ultra Series Wallplate Encoders (717WP2 and 718WP4)
Overview Configure HDMI and VGA selection, startup behavior, and audio on the Ultra Series UL-717WP2 and UL-718WP4 Wallplate Encoders. These models were previously identified as VBS-HDIP-717WP2 and VBS-HDIP-718WP4. * 717WP2: 2-gang; HDMI, VGA, Line-In, Micro USB, source switch, and PoE network connection. * 71…
03-Nov-2026
-
Ultra Series Encoder Audio Planning
Overview Ultra Series Encoders handle audio differently depending on the model. Choose the Encoder at each source location according to the audio format produced by the source and how that audio must be distributed. Most installations fall into one of these categories: * Audio pass-through: Preserve the original…
02-Sep-2026
-
2G Series Encoder-to-Decoder Latency
Overview Just Add Power Encoders convert HDMI signals into network packets for transport across the network. Decoders convert those packets back into HDMI for display. This encoding and decoding process introduces a small amount of video latency. Latency Specification 2G Series systems have approximately 37 milli…
26-Aug-2026
-
Add Devices On-site with AMP Standardized Configuration
Overview Use AMP to add new Encoders and Decoders to an established Standardized Configuration system while on-site. AMP retrieves the system information through an active device, identifies available expansion ports, and configures each new device for the port you select. This procedure covers Omega Series, Ultra …
03-Nov-2026
-
ST1 Audio Encoder / Decoder - Audio Distribution Examples
Overview The Just Add Power Sound Encoder/Decoder - model ST1 - is capable of sending or receiving stereo audio from a Just Add Power system. As a Transceiver, you begin by choosing whether it will act as a Encoder or Decoder - an input or an output - and build the system accordingly. Audio Capabilities * Stereo …
31-Aug-2026
-
IPv4 Address Table for AMP Standardized Systems
Overview Advanced Matrix Programmer uses a unique IP Scheme for all Just Add Power Series devices being setup using the software. Just Add Power Network IP: 172.27.0.0 Just Add Power Subnet Mask: Class B | 255.255.0.0 | /16 The specific subnet does not affect the system as long as 2 rules are followed: * Eac…
25-Sep-2025
-
Access an Encoder or Decoder webUI (2G Series and 2G Legacy Mode)
Overview Use an Encoder or Decoder webUI to view device information and manage available settings. The pages and features available depend on the device model and firmware. To open the webUI, you need the device's IP address and a network connection that can reach it. Choose the instructions that match your conne…
02-Oct-2026
-
How to Modify an Encoder EDID (2G Series and 2G Legacy Mode)
Overview 2G Series Encoders include built-in EDIDs to improve compatibility with a wide range of source devices. These EDIDs allow you to control how a source negotiates video and audio capabilities, helping ensure stable operation across different displays and system designs. There are three supported methods fo…
02-Oct-2026
-
How VLAN Switching Works in AMP Standardized Systems
Overview In an AMP Standardized Configuration, audio and video sources are routed using VLAN Switching. Each Encoder is assigned a dedicated source VLAN. To select a source, the switch changes the VLAN membership of the port connected to the Decoder so that it matches the VLAN assigned to the desired Encoder. Audio…
27-Aug-2026
-
How to Use Image Pull
Overview Image Pull provides a preview of the HDMI video being processed by a Just Add Power Encoder or Decoder. The preview can be viewed in the device webUI, opened directly in a web browser, or displayed within a control system interface. Image Pull is also a useful troubleshooting tool. Comparing the preview fr…
17-Jul-2026
⚠️ JADConfig will reach End of Support on January 1, 2027. View the official notice! ⚠️
